Manual Shift Knob Restoration
Manual Shift **** Restoration
The shift **** on my coupe was badly scratched by the original owner. I thought it was just painted plastic. Sanding it I discovered it has a thin aluminum shell. The scratches went into the aluminum. I considered buying an aftermarket ****, but thought it was worth trying to restore this one first.
So this is what the **** looked like when I started.
After sanding with 400 grit wet/dry sandpaper and painting with a scratch fill primer.
The finished **** painted silver again and topped with a clear coat.
I'm happy with the results.
So this is what the **** looked like when I started.
After sanding with 400 grit wet/dry sandpaper and painting with a scratch fill primer.
The finished **** painted silver again and topped with a clear coat.
I'm happy with the results.
Last edited by Toolman; 12-14-2014 at 09:14 PM.
Re: Manual Shift **** Restoration
The **** has held up well with no scratches, but the car is not a daily driver.
No plans to fill in the numbers. I have too many other projects in process.
The **** is easily removed if you know the trick. You have to remove the base of the leather boot cover away from the center console. You do that by pressing the sides of the bottom of the boot towards the shifter to release the boot retainer clips from the console. You then lift the boot up and above the shifter ****. Underneath the leather boot cover, at the base of the shift ****, you will see a round screw on nut which is made out of plastic. Gently unscrew that "with you fingers" from the ****. With that nut unscrewed from the **** you can now just pull the **** up and off the shifting shaft.
No plans to fill in the numbers. I have too many other projects in process.
The **** is easily removed if you know the trick. You have to remove the base of the leather boot cover away from the center console. You do that by pressing the sides of the bottom of the boot towards the shifter to release the boot retainer clips from the console. You then lift the boot up and above the shifter ****. Underneath the leather boot cover, at the base of the shift ****, you will see a round screw on nut which is made out of plastic. Gently unscrew that "with you fingers" from the ****. With that nut unscrewed from the **** you can now just pull the **** up and off the shifting shaft.
Last edited by Toolman; 09-01-2015 at 05:27 PM.
Join Date: Jul 2015
Location: Pittsburgh, PA
Age: 60
Posts: 945
Likes: 0
Received 4 Likes
on
4 Posts
Re: Manual Shift **** Restoration
The shift **** on my coupe was badly scratched by the original owner. I thought it was just painted plastic. Sanding it I discovered it has a thin aluminum shell. The scratches went into the aluminum. I considered buying an aftermarket ****, but thought it was worth trying to restore this one first.
So this is what the **** looked like when I started.
.
So this is what the **** looked like when I started.
.
Re: Manual Shift **** Restoration
I have an autostick. On occasion I actually polish my ****. But I also keep a small microfiber towel on the center console that I keep between the palm of my hand and my **** when shifting. Therefore, my aging **** looks almost new. My wife thinks that polishing my **** and using the towel as a barrier is a bit ****.
Re: Manual Shift **** Restoration
I do not have pictures of it sanded down to bare metal. I only sanded the top half where it was scratched and the metal itself was scratched, so going for a bare metal look would not work.
I used regular automotive paint. First using a scratch fill primer, the base silver coat, and then the clear.
A helpful hint when painting it is to do very light coats or you can easily fill in the numbers. In addition, do not press on the spray can button while pointing it at the ****. Start the spray off to the side and spray across the ****. The spray button should be at least 8 inches from the ****.
I used regular automotive paint. First using a scratch fill primer, the base silver coat, and then the clear.
A helpful hint when painting it is to do very light coats or you can easily fill in the numbers. In addition, do not press on the spray can button while pointing it at the ****. Start the spray off to the side and spray across the ****. The spray button should be at least 8 inches from the ****.
Last edited by Toolman; 09-03-2015 at 08:02 PM.
Join Date: Sep 2007
Location: MOFN, AL, 70 miles from George
Age: 66
Posts: 8,017
Likes: 0
Received 6 Likes
on
6 Posts
Join Date: Jul 2015
Location: Pittsburgh, PA
Age: 60
Posts: 945
Likes: 0
Received 4 Likes
on
4 Posts
Re: Manual Shift **** Restoration
A/c **** lube ? | Mercedes-Benz Club of America
Join Date: Sep 2007
Location: MOFN, AL, 70 miles from George
Age: 66
Posts: 8,017
Likes: 0
Received 6 Likes
on
6 Posts
Re: Manual Shift **** Restoration
Hah! Yes it was. I wasn't familiar with how the (over)censorship on this site works. So I wrote a post using the censored word to be silly and poke fun at needing to be censored. But then I noticed that once I signed in the ****s went away revealing the word that is used as a grip or handle, and it no longer was humorous. So then I just deleted the text and replaced it with my question related to the type of clear coat used. FWIW, the clear coat spray cans that use a catalyst provide a more durable coating; you just need to wear the proper equipment when spraying.
Join Date: Sep 2007
Location: MOFN, AL, 70 miles from George
Age: 66
Posts: 8,017
Likes: 0
Received 6 Likes
on
6 Posts
Re: Manual Shift **** Restoration
Hah! Yes it was. I wasn't familiar with how the (over)censorship on this site works. So I wrote a post using the censored word to be silly and poke fun at needing to be censored. But then I noticed that once I signed in the ****s went away revealing the word that is used as a grip or handle, and it no longer was humorous. So then I just deleted the text and replaced it with my question related to the type of clear coat used. FWIW, the clear coat spray cans that use a catalyst provide a more durable coating; you just need to wear the proper equipment when spraying.
It seems to set up softer. But more easily repaired/polished. Maybe it's just me.
Thread
Thread Starter
Forum
Replies
Last Post
crossfireusa
Engine, Exhaust, Transmission and Differential
6
10-28-2015 12:03 AM
jimf
Troubleshooting & Technical Questions & Modifications
11
10-10-2015 10:22 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)