CrossfireForum - The Chrysler Crossfire and SRT6 Resource

CrossfireForum - The Chrysler Crossfire and SRT6 Resource (https://www.crossfireforum.org/forum/)
-   Exterior & Lighting (https://www.crossfireforum.org/forum/exterior-lighting/)
-   -   high beam flash (https://www.crossfireforum.org/forum/exterior-lighting/65475-high-beam-flash.html)

Furgal 01-10-2014 12:17 PM
high beam flash
 
I replaced my low beam headlight bulbs, all lamps are working, but now can't flash high beams with the turn signal stalk. High beams go on when pushing stalk forward.

pizzaguy 01-10-2014 12:22 PM
Re: high beam flash
 
I don't see how this can have anything to do with replacing bulbs.

THIS is a GOOD one! ;)

RED DOG 01-10-2014 01:13 PM
Originally Posted by Furgal (Post 775589)
I replaced my low beam headlight bulbs, all lamps are working, but now can't flash high beams with the turn signal stalk. High beams go on when pushing stalk forward.
there was another recent post about that. I forget what the fix is. I'll find it and post here later.

maxcichon 01-10-2014 02:37 PM
Re: high beam flash
 
Are your FOG LIGHTS turned on?

RED DOG 01-10-2014 03:04 PM
Re: high beam flash
 
Originally Posted by maxcichon (Post 775606)
Are your FOG LIGHTS turned on?
I can't find the post I recently read but I was just going to ask him if his fog lights were on. Seems to me if the fog lights are on that pulling the stalk back will not activate / flash the high beams.

ala_xfire 01-10-2014 03:11 PM
Re: high beam flash
 
Pulling the stalk toward me does NOT flash the high beams fog lights or no, UNLESS the engine is running, then the high beams will flash regardless of the fog lights on/off.

RED DOG 01-10-2014 03:13 PM
Re: high beam flash
 
Originally Posted by ala_xfire (Post 775617)
Pulling the stalk toward me does NOT flash the high beams fog lights or no, UNLESS the engine is running, then the high beams will flash regardless of the fog lights on/off.
OK so the engine has to be running to activate the high beams by pulling the stalk back toward you?

ala_xfire 01-10-2014 03:17 PM
Re: high beam flash
 
Originally Posted by RED DOG (Post 775618)
OK so the engine has to be running to activate the high beams by pulling the stalk back toward you?
Yes, at least on my roadster, other's experience may differ.
( These are tricky little suckers )

onehundred80 01-10-2014 04:57 PM
Re: high beam flash
 
It isn't called the 'passing' light for nothing, I have not passed anything in my car with the engine off.:p

S. Artee 01-10-2014 05:14 PM
Originally Posted by ala_xfire (Post 775620)
yes, at least on my roadster, other's experience may differ.
( these are tricky little suckers )
+1............

SparkieSRT6 01-10-2014 05:14 PM
Re: high beam flash
 
Originally Posted by onehundred80 (Post 775636)
It isn't called the 'passing' light for nothing, I have not passed anything in my car with the engine off.:p


C'mon Dave, lets be honest. You havent pulled out to pass another car in years. :p

pizzaguy 01-10-2014 05:17 PM
Re: high beam flash
 
Originally Posted by SparkieSRT6 (Post 775640)
C'mon Dave, lets be honest. You havent pulled out to pass another car in years. :p
I wish I'd said that.... I owe him SO many....

onehundred80 01-10-2014 05:45 PM
Re: high beam flash
 
Originally Posted by SparkieSRT6 (Post 775640)
C'mon Dave, lets be honest. You havent pulled out to pass another car in years. :p
You are correct, I haven't even passed a kidney stone.:p

kjwinston 01-31-2014 04:09 PM
Re: high beam flash
 
I asked...and Asked again...and asked Again one more time. No one knew of the mystery: "my high beams don't work by selecting the lever ON for high beams? So I had to go to the Chrysler dealer! YIKES!


Well there is a problem and it is not the Fog lamp issue. Yes if your Fog lamps are on your high beams will not come on at the same time, but will come on and turn off the fog lamps automatically.


What is bad is in your turn signal. Yes they have to open the steering wheel (dang Bags) and replace Part Number #5098519aa the switch turn signal. Try to buy the part first otherwise good ole Chrysler will charge you $359.10 for the part. It took these guys 4 hours to replace it.


They work just fine now. I am sure it would be cheaper if someone would have know, so I am passing this on. You guys have always given me great advice, and now I am returning the part number and what has to be replaced. I hope this helps!


That was a Chrysler part number.


Just put on my 36000 mile on the Toy!


KJ

onehundred80 01-31-2014 04:29 PM
Re: high beam flash
 
Originally Posted by kjwinston (Post 779391)
I asked...and Asked again...and asked Again one more time. No one knew of the mystery: "my high beams don't work by selecting the lever ON for high beams? So I had to go to the Chrysler dealer! YIKES!


Well there is a problem and it is not the Fog lamp issue. Yes if your Fog lamps are on your high beams will not come on at the same time, but will come on and turn off the fog lamps automatically.


What is bad is in your turn signal. Yes they have to open the steering wheel (dang Bags) and replace Part Number #5098519aa the switch turn signal. Try to buy the part first otherwise good ole Chrysler will charge you $359.10 for the part. It took these guys 4 hours to replace it.


They work just fine now. I am sure it would be cheaper if someone would have know, so I am passing this on. You guys have always given me great advice, and now I am returning the part number and what has to be replaced. I hope this helps!


That was a Chrysler part number.


Just put on my 36000 mile on the Toy!


KJ
So I guess at $359.10 for the part plus labor this fix is more than just a simple flash in the pan repair. Ouch!
PS
You do not want to see what others sell it for.
Spoiler alert.







The Mercedes and the Chrysler can be had for about $230 elsewhere.
The Mercedes part is probably #170 540 03 44
Chrysler part is #5098519aa as you said.
I did warn you.


All times are GMT -4. The time now is 11:08 AM.


© 2024 MH Sub I, LLC dba Internet Brands