|
Car Won't Start After Fixing "Sticky Ignition Switch" HELP!!!
My Car wont start!
its not even cranking the engine at all . all the lights on the dash board come on and the alarm works But the car doesn't make a sound when i try to turn it on! i was searching and i found out that it might be this : attached -------------> How to Repair Relay Control Module (RCM) - (Mystery no Start) but does this cause after fixing the ignition switch is it a common issue or was it my luck that it happen at the same time PLEASE HELP!:confused: |
Re: Car Won't Start After Fixing "Sticky Ignition Switch" ! HELP!!!!
Originally Posted by MXQB7
(Post 748155)
My Car wont start!
its not even cranking the engine at all . all the lights on the dash board come on and the alarm works But the car doesn't make a sound when i try to turn it on! i was searching and i found out that it might be this : attached -------------> How to Repair Relay Control Module (RCM) - (Mystery no Start) but does this cause after fixing the ignition switch is it a common issue or was it my luck that it happen at the same time PLEASE HELP!:confused: Also, there is the halo ring that goes around the ignition keyhole, is that on? The other end of the halo wire plugs into the SKREEM module if that has become damaged or unplugged the car will not start. Someone forgot to put the halo back on a few years back, but I think it cranked but did not start. |
Re: Car Won't Start After Fixing "Sticky Ignition Switch" ! HELP!!!!
yes I did put the the wire from the back on!
the one thing I couldn't find was were the key hole ring goes. The cable I mean of course is so small and skinny plug. but cant remember or cant find the plug in entrance ? but I would think that for the green light it has right? I don't think It would affect the cars ignition . Im very frustrated and just want the car to run... if its not one thing its the other:confused: |
Re: Car Won't Start After Fixing "Sticky Ignition Switch" ! HELP!!!!
Originally Posted by MXQB7
(Post 748174)
yes I did put the the wire from the back on!
the one thing I couldn't find was were the key hole ring goes. The cable I mean of course is so small and skinny plug. but cant remember or cant find the plug in entrance ? but I would think that for the green light it has right? I don't think It would affect the cars ignition . Im very frustrated and just want the car to run... if its not one thing its the other:confused: So to put it simply. No correct chip in the key in the ignition = no start. No halo ring signal = no start. |
Re: Car Won't Start After Fixing "Sticky Ignition Switch" ! HELP!!!!
Originally Posted by onehundred80
(Post 748199)
That halo ring determines if the car has the correctly chipped key in the ignition.
So to put it simply. No correct chip in the key in the ignition = no start. No halo ring signal = no start. Ok so I should hook up the halo ring to see if it turns green.. but I cant find were the other side of the cable goes into.. have u heard of other reasons y u think it wont turn on? even if the halo ring turns on!? |
Re: Car Won't Start After Fixing "Sticky Ignition Switch" ! HELP!!!!
Originally Posted by MXQB7
(Post 748202)
Ok so I should hook up the halo ring to see if it turns green..
but I cant find were the other side of the cable goes into.. have u heard of other reasons y u think it wont turn on? even if the halo ring turns on!? To put it simply. The halo ring is a part of the anti-theft system. If the car would start without the halo ring hooked up, a thief would only have to pull of the wire and drive away. OK? |
Re: Car Won't Start After Fixing "Sticky Ignition Switch" ! HELP!!!!
Ok I completely understand by my thing is where ?
I detached the ring. So the end of the cable is unplugged I cannot find the place it goes, where to insert it ? I've been looking under the steering wheel but cannot find it Plz help ? |
Re: Car Won't Start After Fixing "Sticky Ignition Switch" ! HELP!!!!
Originally Posted by MXQB7
(Post 748224)
Ok I completely understand by my thing is where ?
I detached the ring. So the end of the cable is unplugged I cannot find the place it goes, where to insert it ? I've been looking under the steering wheel but cannot find it Plz help ? If you look at these posts (click) the third or fourth one down asks for pictures of the SKREEM module and there are three pics of it in a post. |
| All times are GMT -4. The time now is 07:35 PM. |
© 2026 MH Sub I, LLC dba Internet Brands