CrossfireForum - The Chrysler Crossfire and SRT6 Resource
Left 3, came out of 5 wire RCM connector. Right 3 were replacements. Cut bad end off the wire, strip back, then solder new connector on wire. Make sure they are inserted back in connector correctly. DONE
Left 3, came out of 5 wire RCM connector. Right 3 were replacements. Cut bad end off the wire, strip back, then solder new connector on wire. Make sure they are inserted back in connector correctly. DONE
0 2025/06/27 19:27:07
0 2025/06/27 19:25:54
0 2025/06/03 17:20:09
0 2024/06/26 13:59:49
0 2024/05/24 16:18:40
0 2024/04/27 20:25:42
0 2024/04/27 20:25:31
0 2024/04/27 20:25:16
0 2024/03/18 13:02:24
Extra cable loop allowing engine/transmission to 'flex' some without stretching cable
Extra cable loop allowing engine/transmission to 'flex' some without stretching cable
0 2024/01/12 15:45:20
Another wire tye where cable slid along channel, holding it up inside channel.
Another wire tye where cable slid along channel, holding it up inside channel.
0 2024/01/12 15:45:17
Used a wire tye to secure cable to POS cable
Used a wire tye to secure cable to POS cable
0 2024/01/12 15:45:15
Trimmed the grey cover allowing cable terminal to protrude without losing the cap.
Trimmed the grey cover allowing cable terminal to protrude without losing the cap.
0 2024/01/12 15:45:13
Ran cable along slot between batt and electronics box.
Ran cable along slot between batt and electronics box.
0 2024/01/12 15:45:10
Scrubbed the metal cable contact point, looked with light & mirror, clean & shiny.
Scrubbed the metal cable contact point, looked with light & mirror, clean & shiny.
0 2024/01/12 15:45:08
No factory thread lock? I added a dab when assembling.
No factory thread lock? I added a dab when assembling.
0 2024/01/12 15:45:05
My 14 Torx and drive either with or without extension was hitting the transmission tube :(
My 14 Torx and drive either with or without extension was hitting the transmission tube :(
0 2024/01/12 15:45:03
Cap removed ready to install Scrubbed terminal and post after removing.
Cap removed ready to install Scrubbed terminal and post after removing.
0 2024/01/12 15:45:00
0 2023/04/19 14:27:17
0 2022/10/27 09:14:24
0 2022/06/29 09:13:56
0 2022/03/15 13:01:50
0 2021/05/31 13:24:18
0 2021/04/30 05:47:28
0 2020/05/26 20:08:29
0 2020/05/26 20:05:51
0 2020/05/26 20:00:53
0 2020/05/20 18:06:59
0 2020/05/20 18:06:46
0 2020/05/20 18:06:35
0 2020/05/14 12:41:01
0 2020/05/14 12:40:31
0 2020/04/30 15:14:33
0 2020/04/30 15:13:30
0 2020/03/18 20:48:53
0 2020/03/18 20:04:40
0 2020/03/18 20:04:12
0 2020/03/18 20:03:24
0 2020/03/18 20:02:03
0 2020/03/18 20:01:10