CrossfireForum - The Chrysler Crossfire and SRT6 Resource
The chrome 90* L shape polished pipes are extra
The chrome 90* L shape polished pipes are extra
0 2025/02/24 08:36:34
Air horns R the only thing that is in front of radiator
Air horns R the only thing that is in front of radiator
0 2025/02/24 08:36:04
0 2025/02/24 08:30:31
in the center is the engine cover . the two pieces to the far right is the in
in the center is the engine cover . the two pieces to the far right is the in
0 2025/02/17 12:04:44
either this is left or right and either one of the two is missing either left or right also shows where the snorkel goes from intake to radiator support in U have an aftermarket yours are probably not there
either this is left or right and either one of the two is missing either left or right also shows where the snorkel goes from intake to radiator support in U have an aftermarket yours are probably not there
0 2025/02/17 12:02:56
fitting i middle of pic hose missing
fitting i middle of pic hose missing
0 2025/02/17 12:01:43
part that goes to throttle body, one holding prong broken off but once installed all good also missing clamps 4 each tube to throttle box.
part that goes to throttle body, one holding prong broken off but once installed all good also missing clamps 4 each tube to throttle box.
0 2025/02/17 11:57:58
missing one snorkel not sure L or R
missing one snorkel not sure L or R
0 2025/02/17 11:57:20
0 2024/09/26 07:47:59
god shot of the notches and the washer welded in
god shot of the notches and the washer welded in
0 2024/09/26 07:43:37
this is the long half of the drive shaft. disregard the white paint ,that is what the shop used to put every thing back to stock configuration
this is the long half of the drive shaft. disregard the white paint ,that is what the shop used to put every thing back to stock configuration
0 2024/09/26 07:41:09
0 2024/09/26 07:40:42
also you can see they did not have the tool to center the u joint so i told them to use thin washers to center and weld the washer not the u joint
also you can see they did not have the tool to center the u joint so i told them to use thin washers to center and weld the washer not the u joint
0 2024/09/26 07:38:46
this is on the short shaft
this is on the short shaft
0 2024/09/26 07:37:55
0 2024/09/16 17:21:59
0 2024/09/16 17:21:36
0 2024/09/16 17:15:42
another 20" tire chart
another 20" tire chart
0 2024/09/16 17:10:53
ball and taper bolt. hope u can see this
ball and taper bolt. hope u can see this
0 2024/09/16 17:09:13
20" tire chart
20" tire chart
0 2024/09/16 17:03:01
18"tire chart
18"tire chart
0 2024/09/16 17:01:42
19" tire chart Tire size max height 26.9 stock 26.0 285/35-19= 26.9 & 11.2 wide see tire chart
19" tire chart Tire size max height 26.9 stock 26.0 285/35-19= 26.9 & 11.2 wide see tire chart
0 2024/09/16 17:00:30
crossfire tire specs
crossfire tire specs
0 2024/09/16 16:59:47
0 2024/09/16 16:59:09
crossfire
crossfire
0 2024/09/16 16:58:42
0 2024/09/16 16:58:18
Bolt taper and ball
Bolt taper and ball
0 2024/09/16 16:57:26
Bolt taper and ball
Bolt taper and ball
0 2024/09/16 16:56:54
0 2024/07/16 13:33:08
0 2024/07/16 13:32:41
0 2024/07/16 13:32:21
0 2024/07/16 13:31:36
0 2024/07/16 13:31:02
0 2024/07/16 13:30:04
0 2024/07/16 13:29:49
0 2024/07/16 13:28:20
0 2024/05/30 13:29:06
0 2024/04/25 14:41:47
0 2024/04/25 14:08:00
0 2024/04/25 14:07:40