In that case, can you buy me a set of Aero Blue's too?

 

Looks like your going to be making all of the colors here pretty soon, may end up being quite lucrative for you! I look forward to you producing some ssb soon!!!

 

How does a chrome one look with my blaze red?

 

Yes, would be very interested in chrome.

 

Thank you all for the interest. I will be posting by the end of this coming week when the black and graphite are ready to ship.
I guess I'll start gathering more material to do ssb too.
Chrome I can't do but I will look into making some out of thin polished stainless...

 

I'll get some graphite ones, but I won't be back in the states until May. And to the guys saying ouch on the price shut up and look around, that's not a bad price. If you want something cheap goto a vinyl shop and have them make some.

 

I'm going to try a set out of stainless steel laser cut with the word crossfire cut out. Might be interesting.

 

It would probably look good in stainless but the crossfire logo may be a bit much...Just my opinion.

 

I'm in for a set of ssb, looks good.

 

Wow. Getting kind of touchy because someone voices an opinion and thinks something is too expensive, aren't you? And then you have the ***** to tell them to "shut up"... okay. I wouldn't buy because of your attitude alone.

 

How much of the turn signal is covered? It seams that it would cover over 50% of it.

Can anybody photoshop a set that goes a little lower but follows the curves of the projectors (and turn signal)?

 

Well, that post was from Black srt.
I am stryfox "the one making the eyebrows" and I didn't make that comment.
I stated before if you think it is too much don't buy them. Lets try not to argue about it.

 

Sorry if I came across as a di*k but this is the one of the very few things you can buy for this car that isn't over priced.

 

Thanks, I am doing all I can to keep the cost down. I let you know when the 1st batch is ready to ship. Should be done by this weekend. I hope you guys understand the wait. I don't want quality to suffer just to get them done faster.

 

Shut up... Stryfox has a great aftermarket item, the material he picked is perfect for the application and with his skills with MOPAR cars and paint. I will bet the quality is as good as the original aftermarket parts from across the pond, and less money.
Now I have laser cut Stainless steel eyebrow covers with or without the crossfire logo ONLY $999.99
a pair. This includes installation and I get to test drive your car to make sure they work.
Please allow for the snow to melt before your parts can be hand delivered and installed.

Oversea customers please add $500.00 shipping.

 

here is a front view:

https://www.crossfireforum.org/galle...cat/500/page/1

 

Looks like the turn signals show just fine. Maybe it was the other angle that was throwing me off. Everyone that thinks these are overpriced, your crazy. Great mod at a great value. Although, I would still like to see something that accents the projectors a little better.

stryfox, I really like your mods. How did you attach the dead pedal? It matches the stock ones very well. I can tell that you do a lot of paint work just by looking at your engine cover, which is also very impressive. Good luck and keep the mods coming!

 

Ok guys,

Thank you for the interest in my crossfire headlamp eyebrows.

I have some graphite and black ready to ship.

These parts are ready to install with pre applied genuine 3M body tape.

If you are interested Pm me and I will hold them for you, and give you the info you need.


I spent more time on these than I estimated but I will stick to my price.

If I produce more in the future I may have to raise the price.

 

I just replied to your PM. Thanks again.

 

I have a set with your name on it. I'll ship it out ASAP.