CrossfireForum - The Chrysler Crossfire and SRT6 Resource

CrossfireForum - The Chrysler Crossfire and SRT6 Resource (https://www.crossfireforum.org/forum/)
-   Troubleshooting & Technical Questions & Modifications (https://www.crossfireforum.org/forum/troubleshooting-technical-questions-modifications/)
-   -   Engine Management Light and Relay burnt out (https://www.crossfireforum.org/forum/troubleshooting-technical-questions-modifications/64673-engine-management-light-relay-burnt-out.html)

Bay Cruise 11-22-2013 09:04 PM

Engine Management Light and Relay burnt out
 
Quick Question please, I have read loads on this subject re the relays solder causing the “engine management light” to come on intermittently. Upon checking mine this morning the solder joints were all ok but the relay contacts were badly burnt. I have filed them for now and everything seems to be working fine, as per the below photos, but my question is can you just get one of these relays and re solder it on the board or do you have to get the full block. If so what’s the part number and where can I get one posted to Australia. Thanks in advance.

http://www.bayphotos.com.au//miscellaneous/relay1.JPG

http://www.bayphotos.com.au//miscellaneous/relay2.JPG

Bay Cruise 11-22-2013 11:01 PM

Re: Engine Management Light and Relay burnt out
 
Should have added that I reset the fault codes, done a few K, and no new codes have appeared since I filed the contacts. Does anyone recon I need to change the relay (or whole relay block if I can't get just the relay on its own) or will what I have done be ok if no more codes show up.

I can get a new one from the States on eBay for $250 delivered to Oz but don't want to if not needed.

tighed1 11-22-2013 11:18 PM

Re: Engine Management Light and Relay burnt out
 
I've gotta get a hold of some of these relays! Dave (180) listed info on this here...

LINKY

While you have the RCM out re-look those solder joints. Can't really see how bad they are unless you magnify them.

Bay Cruise 11-23-2013 12:25 AM

Re: Engine Management Light and Relay burnt out
 
Thanks useful thread. However do you know where I can buy one because the place suggested wants $60 to ship one to Australia.


Originally Posted by tighed1 (Post 768285)
I've gotta get a hold of some of these relays! Dave (180) listed info on this here...

LINKY

While you have the RCM out re-look those solder joints. Can't really see how bad they are unless you magnify them.


ala_xfire 11-23-2013 06:48 AM

Re: Engine Management Light and Relay burnt out
 
I replaced that air pump relay on my RCM, had ordered 12 relays at around $2 each.
They are almost gone now, used one, gave maxchicon some and sent some to onehundred80.
I'll tell ya, it is not for the faint of heart, those suckers are HARD to remove, soldering the new one is easy.

DJ, are you back in the RCM swap business ?
( if not, can I have the spare one I sent you back ? )

Bay Cruise 11-23-2013 03:05 PM

Re: Engine Management Light and Relay burnt out
 
Don't suppose you have a couple I could buy off you to send to Oz. The only place I can see who sells them wants $60 postage for one. Or do you know somewhere that will send them to Oz. I have a payPal account if that is any good for payment.


Originally Posted by ala_xfire (Post 768300)
I replaced that air pump relay on my RCM, had ordered 12 relays at around $2 each.
They are almost gone now, used one, gave maxchicon some and sent some to onehundred80.
I'll tell ya, it is not for the faint of heart, those suckers are HARD to remove, soldering the new one is easy.

DJ, are you back in the RCM swap business ?
( if not, can I have the spare one I sent you back ? )



All times are GMT -4. The time now is 04:31 PM.


© 2024 MH Sub I, LLC dba Internet Brands