CrossfireForum - The Chrysler Crossfire and SRT6 Resource

Crossfire SRT6 A place to discuss SRT-6 specific topics.

Code 3 supercharger pulley

 
Old Aug 9, 2008 | 06:10 PM
Share
  #21 (permalink)  
SRTFreak's Avatar
Joined: Jul 2008
Posts: 58
Likes: 0
From: NC
Default Re: Code 3 supercharger pulley
Originally Posted by SRT-6 Steve
Does anyone know what changed to not use the spacers? It came with three. I believe you would experience a slight rub due to not enough space between the new pully and the clutch. The stock spacer is very thin and there is only one. Not saying it won't work this way but I believe you really need to check the spacing.

Steve
Steve
I asked Brandon ( Code3 ) about him not using the spacers on the new pulleys. He said that the time the first batch got off the line the tail end of them had gotten off by a couple 1000th of an inch. So the solution was to use spacers. The newer pulleys are measuring to spec.
 
Reply
0
Old Aug 9, 2008 | 07:26 PM
Share
  #22 (permalink)  
SRT-6 Steve's Avatar
Forum Regular
Joined: Sep 2007
Posts: 1,020
Likes: 0
From: Athens, Texas
Default Re: Code 3 supercharger pulley
Originally Posted by SRTFreak
Steve
I asked Brandon ( Code3 ) about him not using the spacers on the new pulleys. He said that the time the first batch got off the line the tail end of them had gotten off by a couple 1000th of an inch. So the solution was to use spacers. The newer pulleys are measuring to spec.
Thanks, I appreciate the iinfo. I used three spacers.

Steve
 
Reply
0
Old Aug 9, 2008 | 07:28 PM
Share
  #23 (permalink)  
SRT-6 Steve's Avatar
Forum Regular
Joined: Sep 2007
Posts: 1,020
Likes: 0
From: Athens, Texas
Default Re: Code 3 supercharger pulley
Originally Posted by BLKFIN
I just installed a boost gauge this week and have not had a real chance to open her up, but the most I have seen in the lower gears in 15lbs. When are you seeing 17lbs? The top of third gear?
Hi BLKFIN, Do you have any pictures? Did you do the install?

Steve
 
Reply
0
Old Aug 10, 2008 | 08:43 AM
Share
  #24 (permalink)  
BLKFIN's Avatar
ADDICTED TO BOOST
Joined: May 2005
Posts: 1,625
Likes: 1
From: McKinney, TX
Default Re: Code 3 supercharger pulley
Originally Posted by SRT-6 Steve
Hi BLKFIN, Do you have any pictures? Did you do the install?

Steve
I will take some today and post them in my Gallery. I will send you a pm once I have them up. I did the install....not too bad. I had a little free time when Jerry had my ECU. I finally had a chance to see 17lbs of boost yesterday~
 
Reply
0
Old Aug 10, 2008 | 11:23 AM
Share
  #25 (permalink)  
Eleventeen's Avatar
Joined: May 2008
Posts: 118
Likes: 0
From: Voorhees, NJ
Default Re: Code 3 supercharger pulley
Even the factory pulley uses spacers, so if he got them spec'd out so well that none are needed, then he's done a pretty good job.
 
Reply
0
Old Aug 11, 2008 | 03:28 PM
Share
  #26 (permalink)  
oledoc2u's Avatar
Senior Member
Joined: Mar 2008
Posts: 14,599
Likes: 34
From: IN
Default Re: Code 3 supercharger pulley
well, you use the ones that are already on there...so there are spacers (shims)...just don't need more....
 
Reply
0
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Code 3 65mm s/c pulley
TOPLESS
Parts/Accessories for sale - Archive
4
Feb 9, 2016 11:28 AM
Srt-6 tuner tampa area still looking
UNDER PSI
Crossfire SRT6
8
Nov 1, 2015 09:39 PM
Serpentine belt # for Rob's PSK
Sweet2002
Crossfire SRT6
3
Sep 26, 2015 10:21 PM
I need needswings phone number!
Sweet2002
Crossfire SRT6
0
Sep 25, 2015 07:46 AM
ORDERED A SET OF 550's NEW!
Sweet2002
Crossfire SRT6
0
Sep 25, 2015 02:16 AM
Back to Subforum
Crossfire SRT6
View Next Unread
Johnson Pump Instructions and Pulley Question

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Thread Tools

Advanced Search

All times are GMT -4. The time now is 01:01 AM.