P0410 code
I just got my car back running after about 2+ months of sitting. It was drivin from the repair shop straight home. While parked and sitting at idle I hear what sounds like a water pump sound from inside the car. It sounds like a liquid squish sound that goes on over and over. My check engine light came on so I hooked up my OBDII and it has a P0410 code. It describes it as "Generic" Secondary air injection system. I would say that the sound, sounds llike the water pump because it sounds like a pump trying to compress or push liquid. I have no idea, any help would be appreciated.
Last edited by BlUEMDsrt6; Feb 4, 2009 at 06:03 PM.
http://freeautomechanic.blogspot.com...uble-code.html
What this means -
The P0410 code refers to the emissions system. The AIR pump puts air to the exhaust to lower emissions. It takes in outside air and pumps it through two one-way check valves into each bank of the exhaust.
About 90% of the time that this code is set, the one-way check valves have worn out or failed and allow water (which occurs naturally in the exhaust) back into the pump. In any cold climate, especially in climates with higher humidity, this water may be more excessive. The water partially fills the AIR pump, it can then freeze. When the PCM commands the pump on, if the pump is frozen it cannot turn, thus overloading the circuit and "popping" the fuse.
What this means -
The P0410 code refers to the emissions system. The AIR pump puts air to the exhaust to lower emissions. It takes in outside air and pumps it through two one-way check valves into each bank of the exhaust.
About 90% of the time that this code is set, the one-way check valves have worn out or failed and allow water (which occurs naturally in the exhaust) back into the pump. In any cold climate, especially in climates with higher humidity, this water may be more excessive. The water partially fills the AIR pump, it can then freeze. When the PCM commands the pump on, if the pump is frozen it cannot turn, thus overloading the circuit and "popping" the fuse.
Originally Posted by BlUEMDsrt6
So how do I fix this? Do I have to change a fuse? Is this a really bad thing?
OK, I'll try clearing the code and driving it around. I have another question too, I had almmost a full tank of gas and it was also sitting in the car for the 2 month period, should I stay off the pedal till this gas is used up?
Originally Posted by BlUEMDsrt6
OK, I'll try clearing the code and driving it around. I have another question too, I had almmost a full tank of gas and it was also sitting in the car for the 2 month period, should I stay off the pedal till this gas is used up?
It seems to run fine. The only thing i can tell is the theres a lil white smoke coming out the exhaust and it stinks. It doesnt have a rough idle or anyhthing tho.
Originally Posted by BlUEMDsrt6
It seems to run fine. The only thing i can tell is the theres a lil white smoke coming out the exhaust and it stinks. It doesnt have a rough idle or anyhthing tho.
Blue, the P0410 code is not a major issue. You can drive with it and not hurt anything. I got the code by knocking off the line going to one of the vaccum switches on the front of the engine. The CEL is annoying though.
MikeR
MikeR
Thread
Thread Starter
Forum
Replies
Last Post
rampntlion
Engine, Exhaust, Transmission and Differential
21
Feb 11, 2019 08:18 AM
crossfireusa
Engine, Exhaust, Transmission and Differential
6
Oct 28, 2015 12:03 AM
tritongreen
Troubleshooting & Technical Questions & Modifications
0
Sep 18, 2015 07:32 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)




