What did you do to your Crossfire today?
Re: What did you do to your Crossfire today?
I have the car a nice detailing inside and out and finally polished up the headlights. They were looking sad.
DSCN0417-s.jpg
DSCN0417-s.jpg
Re: What did you do to your Crossfire today?
I used a 3M kit on the headlights today. The passenger's side was horrible while the driver's side was "normal" looking. I'm a bit puzzled as the car only had 17,500 miles on it when I bought it and for the past year it's been in a garage except when it's being driven.
Anyway, the 3M kit did a beautiful job. It brought both units back to factory clarity. Not bad for $25. After going through the process, I'd advise using a kit that includes a drill. I can't imagine doing that amount of abrasion by hand.
Anyway, the 3M kit did a beautiful job. It brought both units back to factory clarity. Not bad for $25. After going through the process, I'd advise using a kit that includes a drill. I can't imagine doing that amount of abrasion by hand.
Re: What did you do to your Crossfire today?
Originally Posted by Spudracer
I used a 3M kit on the headlights today. The passenger's side was horrible while the driver's side was "normal" looking. I'm a bit puzzled as the car only had 17,500 miles on it when I bought it and for the past year it's been in a garage except when it's being driven.
Anyway, the 3M kit did a beautiful job. It brought both units back to factory clarity. Not bad for $25. After going through the process, I'd advise using a kit that includes a drill. I can't imagine doing that amount of abrasion by hand.
Anyway, the 3M kit did a beautiful job. It brought both units back to factory clarity. Not bad for $25. After going through the process, I'd advise using a kit that includes a drill. I can't imagine doing that amount of abrasion by hand.
Re: What did you do to your Crossfire today?
Originally Posted by itsky
Unfortunately our cars are prone to the headlight issue. My '06 never did have the problem though, so maybe later models had the plastic improved a bit. I used the 3M kit as well followed up by Meguiars PlasticX.
Re: What did you do to your Crossfire today?
Originally Posted by lildaddym
I just can't figure out how to clean the insides...can I take the assembly apart? I know, probably wrong thread...
https://www.crossfireforum.org/forum...ight-lens.html
Re: What did you do to your Crossfire today?
Originally Posted by itsky
The oxidation should be on the outside. I know it looks to be on the inside, but I have polished up sets from an '04 and my current '05 and it gets rid of it. Now if you have condensation on the inside, check out:
https://www.crossfireforum.org/forum...ight-lens.html
https://www.crossfireforum.org/forum...ight-lens.html
Re: What did you do to your Crossfire today?
Originally Posted by lildaddym
Throttle reset?
resets your throttle to "learn" your driving style.
1. turn key to on/run
2. press gas pedal to floor
3. hold pedal down for 5 seconds
4. turn key off - release pedal
5. wait 2 minutes
6. ready to drive
for more info search - "throttle reset"
Re: What did you do to your Crossfire today?
Originally Posted by coolx
resets your throttle to "learn" your driving style.
1. turn key to on/run
2. press gas pedal to floor
3. hold pedal down for 5 seconds
4. turn key off - release pedal
5. wait 2 minutes
6. ready to drive
for more info search - "throttle reset"
1. turn key to on/run
2. press gas pedal to floor
3. hold pedal down for 5 seconds
4. turn key off - release pedal
5. wait 2 minutes
6. ready to drive
for more info search - "throttle reset"