Axle Swap from a Standard Crossfire to SRT6
Axle Swap from a Standard Crossfire to SRT6
First of all hello and hope everyone is safe and healthy. Hope to be at the Ozark meet again this year.
ANYWAY... This is Flying Saucers (Grady) friend Dave (painted the orange crossfire). I'm serious into Crossfires now...
I picked up a rather tortured SRT6 coupe. The rear of the car almost had the axle ripped out of it. I'm trying to rescue it...
I used an entire rear axle and cradle assembly from a roadster in this SRT6. Its in there now.. Has anyone done this before? I assume the axle gear ratio is going to anger the computers?
Is it necessary to have a TCU flashed or can the one from the Roadster be installed and work ?
ANYWAY... This is Flying Saucers (Grady) friend Dave (painted the orange crossfire). I'm serious into Crossfires now...
I picked up a rather tortured SRT6 coupe. The rear of the car almost had the axle ripped out of it. I'm trying to rescue it...
I used an entire rear axle and cradle assembly from a roadster in this SRT6. Its in there now.. Has anyone done this before? I assume the axle gear ratio is going to anger the computers?
Is it necessary to have a TCU flashed or can the one from the Roadster be installed and work ?
Re: Axle Swap from a Standard Crossfire to SRT6
The Rear subframe and axle assembly was pulled from a limited roadster and put into a SRT6 Coupe. Anyone have personal experience with a gear ratio change? Does it require a TCU or Flash or can I get by some other way?
Last edited by dhanson12435; 04-15-2020 at 12:24 PM.
Re: Axle Swap from a Standard Crossfire to SRT6
the limited axles 2005 and up (one piece axle) are the same,,,kinda 2005 has same P/N 2007and up is a larger but hollow axleand stronger, the srt6 has a 3.07 diff the limited has a 3.27 the tcu has to be set up to the car(srt or limited) I can supply you a tcu for a srt6 set up for the 3.27 diff or you can just use the diff from the srt6 with the axles from the limited . the yoke is different on the srt and the limited. as stock they do not interchange yet the axles do.
https://www.crossfireforum.org/forum...ferential.html
https://www.crossfireforum.org/forum...tune-info.html
https://www.crossfireforum.org/forum...ferential.html
https://www.crossfireforum.org/forum...tune-info.html
Re: Axle Swap from a Standard Crossfire to SRT6
Update.. I was curious and installed the TCU from the limited into the SRT6 and I do not get a gear ratio error code anymore. I wonder if a TCU from a Limited will do the trick?
But.... regardless of TCU modules I'm getting a P2562 "The gear is implausible or the transmission is slipping" Transmission acting very odd, sometimes works ok and sometimes completely pissed off. I dropped the trans pan, checked filter and pan for debris. looked clean.. I captured about 4 1/2 quarts of fluid, normal I think. Put it all back for time being till I figure out whats up..
So I'm thinking its one of the three. Transmission was damaged in the accident, perhaps conductor plate issues or gear shifter malfunctions....unless someone has other thoughts.
But.... regardless of TCU modules I'm getting a P2562 "The gear is implausible or the transmission is slipping" Transmission acting very odd, sometimes works ok and sometimes completely pissed off. I dropped the trans pan, checked filter and pan for debris. looked clean.. I captured about 4 1/2 quarts of fluid, normal I think. Put it all back for time being till I figure out whats up..
So I'm thinking its one of the three. Transmission was damaged in the accident, perhaps conductor plate issues or gear shifter malfunctions....unless someone has other thoughts.
Re: Axle Swap from a Standard Crossfire to SRT6
Update.. I was curious and installed the TCU from the limited into the SRT6 and I do not get a gear ratio error code anymore. I wonder if a TCU from a Limited will do the trick?
But.... regardless of TCU modules I'm getting a P2562 "The gear is implausible or the transmission is slipping" Transmission acting very odd, sometimes works ok and sometimes completely pissed off. I dropped the trans pan, checked filter and pan for debris. looked clean.. I captured about 4 1/2 quarts of fluid, normal I think. Put it all back for time being till I figure out whats up..
So I'm thinking its one of the three. Transmission was damaged in the accident, perhaps conductor plate issues or gear shifter malfunctions....unless someone has other thoughts.
But.... regardless of TCU modules I'm getting a P2562 "The gear is implausible or the transmission is slipping" Transmission acting very odd, sometimes works ok and sometimes completely pissed off. I dropped the trans pan, checked filter and pan for debris. looked clean.. I captured about 4 1/2 quarts of fluid, normal I think. Put it all back for time being till I figure out whats up..
So I'm thinking its one of the three. Transmission was damaged in the accident, perhaps conductor plate issues or gear shifter malfunctions....unless someone has other thoughts.
Thread
Thread Starter
Forum
Replies
Last Post
amx1397
Troubleshooting & Technical Questions & Modifications
13
07-16-2018 09:51 PM
RiderJC
WTB - Items/Parts Wanted to Buy - Archive
1
08-14-2015 07:53 PM
MAXIMUSQUO
Troubleshooting & Technical Questions & Modifications
13
09-25-2007 07:05 PM
SWELLCLUB
Wheels, Brakes, Tires and Suspension
9
07-27-2006 02:26 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)