Troubleshooting & Technical Questions & Modifications Have technical or modification questions about the Crossfire? Find out the answer, or give advice in here!

Central locking vacuum pump not working with key

Thread Tools
 
Old Nov 19, 2023 | 03:10 PM
  #1 (permalink)  
JohnMcV's Avatar
Thread Starter
Joined: Jun 2014
Posts: 4
Likes: 2
From: Camarillo, CA
Default Central locking vacuum pump not working with key

Forgive me if this exact problem is discussed elsewhere.
Both FOB keys now won’t lock or unlock the doors. The car lights flash like they used to but there's no noise or results. When I start to drive, the doors and rear hatch lock themselves as they should and when I stop and open either door, they all unlock. I removed the passenger side trunk panels and all looks clean and new where the little hoses travel and no apparent water damage. I'm about to buy a used (with warranty) vacuum pump and do a swap. Should I just go for it, or is there another potential problem? Coincidentally, this problem started when I had the rear shocks repaired.
Thanks!
John
 
Reply
Old Nov 19, 2023 | 03:12 PM
  #2 (permalink)  
ZERACER's Avatar
Senior Member
Joined: Nov 2006
Posts: 6,631
Likes: 776
From: Orange County CA.
Default Re: Central locking vacuum pump not working with key

When were the batteries last replaced in your key FOB?
 
Reply
Old Nov 19, 2023 | 04:42 PM
  #3 (permalink)  
JohnMcV's Avatar
Thread Starter
Joined: Jun 2014
Posts: 4
Likes: 2
From: Camarillo, CA
Default Re: Central locking vacuum pump not working with key

Originally Posted by ZERACER
When were the batteries last replaced in your key FOB?
I just changed the battery in one of the FOBs, but I don't know how long I had those spare batteries.
Is it possible that the battery in the FOB is strong enough to cause the lights to flash on the Crossfire when I press the key but not strong enough to trigger the door locks?
Thanks,
John
 
Reply
Old Nov 19, 2023 | 06:31 PM
  #4 (permalink)  
mikemadeit94's Avatar
Joined: Jul 2020
Posts: 156
Likes: 16
From: East Coast
Default Re: Central locking vacuum pump not working with key

Originally Posted by JohnMcV
I just changed the battery in one of the FOBs, but I don't know how long I had those spare batteries.
Is it possible that the battery in the FOB is strong enough to cause the lights to flash on the Crossfire when I press the key but not strong enough to trigger the door locks?
Thanks,
John
I just had a mess with my locking unit finally got it worked out in a separate thread. Stupid question, but I did it... did you replace BOTH batteries?
 
Reply
Old Nov 19, 2023 | 06:35 PM
  #5 (permalink)  
JohnMcV's Avatar
Thread Starter
Joined: Jun 2014
Posts: 4
Likes: 2
From: Camarillo, CA
Default Re: Central locking vacuum pump not working with key

Yes, I replaced both batteries and can see the light flash inside the key when I press it. I'm going to inspect the harness connections on the vacuum pump and try spraying some contact cleaner in there this weekend. If that doesn't do it, I don't know what to do except buy a new/used vacuum pump and swap it in. I've had the Crossfire coupe for over 10 years.
Thanks,
 

Last edited by JohnMcV; Nov 20, 2023 at 10:03 PM.
Reply
Old Nov 21, 2023 | 06:45 PM
  #6 (permalink)  
JohnMcV's Avatar
Thread Starter
Joined: Jun 2014
Posts: 4
Likes: 2
From: Camarillo, CA
Default Re: Central locking vacuum pump not working with key

Problem solved. I noticed that the interior light wasn't working and that someone else on the forum suggested that checking and replacing fuse #9 might solve both problems. And it did. Thank you zip439!
 
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
RougeXF05
Interior
16
May 27, 2021 07:58 PM
AlexParra
Crossfire Coupe
7
Jul 13, 2020 09:06 PM
Spooky13
Crossfire Coupe
36
Aug 4, 2017 07:25 AM
dj94
Exterior & Lighting
4
Aug 27, 2016 01:30 AM
Drew08
Crossfire SRT6
1
May 22, 2016 02:34 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 



All times are GMT -4. The time now is 09:11 AM.