Engine cover rubbing on SC pulley
Thread Starter
Joined: May 2018
Posts: 52
Likes: 0
From: Mescal, AZ (about 28 miles E of Tucson)
Engine cover rubbing on SC pulley
Getting the new 6 tidied up a bit...
oil and filter changed,
front calipers painted (thanks Chrystal!)
noticed that the engine cover has rub marks from the hood insulation
FYI the original flat tire kit is still in its original wrappings..never been touched
the sc pulley looks like its been rubbing on the engine cover...thin strips of what looks like plastic around its complete circumference at the rear edge of the pulley.
new rear rubber scheduled for this morning...Discount Tire had to order the Barum Bravius tires (made by Continental and at $81 for 255/40-20 Ill give it a shot to get the 6 on the road and can switch or upgrade later
PS how do you get the plywood, foam inserts out of the truck recess to check the unlocking pump for water intrusion??
oil and filter changed,
front calipers painted (thanks Chrystal!)
noticed that the engine cover has rub marks from the hood insulation
FYI the original flat tire kit is still in its original wrappings..never been touched
the sc pulley looks like its been rubbing on the engine cover...thin strips of what looks like plastic around its complete circumference at the rear edge of the pulley.
new rear rubber scheduled for this morning...Discount Tire had to order the Barum Bravius tires (made by Continental and at $81 for 255/40-20 Ill give it a shot to get the 6 on the road and can switch or upgrade later
PS how do you get the plywood, foam inserts out of the truck recess to check the unlocking pump for water intrusion??
Forum Regular
Joined: May 2007
Posts: 766
Likes: 9
From: Picayune MS
Re: Engine cover rubbing on SC pulley
The trunk side panels need to be removed to get the foam inserts out. As far as the engine cover is concerned, I'd just remove it, and get a supercharger plaque 
Senior Member
Joined: Apr 2006
Posts: 25,432
Likes: 647
From: Ontario
Re: Engine cover rubbing on SC pulley
Getting the new 6 tidied up a bit...
oil and filter changed,
front calipers painted (thanks Chrystal!)
noticed that the engine cover has rub marks from the hood insulation
FYI the original flat tire kit is still in its original wrappings..never been touched
the sc pulley looks like its been rubbing on the engine cover...thin strips of what looks like plastic around its complete circumference at the rear edge of the pulley.
new rear rubber scheduled for this morning...Discount Tire had to order the Barum Bravius tires (made by Continental and at $81 for 255/40-20 Ill give it a shot to get the 6 on the road and can switch or upgrade later
PS how do you get the plywood, foam inserts out of the truck recess to check the unlocking pump for water intrusion??
oil and filter changed,
front calipers painted (thanks Chrystal!)
noticed that the engine cover has rub marks from the hood insulation
FYI the original flat tire kit is still in its original wrappings..never been touched
the sc pulley looks like its been rubbing on the engine cover...thin strips of what looks like plastic around its complete circumference at the rear edge of the pulley.
new rear rubber scheduled for this morning...Discount Tire had to order the Barum Bravius tires (made by Continental and at $81 for 255/40-20 Ill give it a shot to get the 6 on the road and can switch or upgrade later
PS how do you get the plywood, foam inserts out of the truck recess to check the unlocking pump for water intrusion??
It may seem a tacky way of doing it but it held the liner up and away from the cover and all was good again.
Thread
Thread Starter
Forum
Replies
Last Post
coryforman
Parts/Accessories for sale - Archive
4
Apr 7, 2017 08:19 AM
MAYAman
Wheels, Brakes, Tires and Suspension
9
Sep 22, 2005 05:02 PM
brittt1
Crossfire Coupe
0
Apr 28, 2005 03:02 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
