Windshield trim loose
Windshield trim loose
My windshield center trim has been singing in the wind for a while and my solution has been to tape it down. Today I had my windshield changed for the second time and the center section almost went awol on the way home. So, I need experienced opinions on a proper permanent solution. I've heard of using double sided tape, I don't see evidence of it being used from the factory however. Who has lived through this scenario and what was the resolution?
Les
Les
On mine the clips came off the trim.
Clean through, trim and clips.
Use sandpaper and scuff the trim where clips attach and scuff clips.
I used epoxy and attached clips back on.
If I remember there are a couple dots on trim u can line up clips with.
Done mine about a year and a half ago.
I do not trust double sided tape holding on a irreplaceable item as windshield trim.
Clean through, trim and clips.
Use sandpaper and scuff the trim where clips attach and scuff clips.
I used epoxy and attached clips back on.
If I remember there are a couple dots on trim u can line up clips with.
Done mine about a year and a half ago.
I do not trust double sided tape holding on a irreplaceable item as windshield trim.
Re: Windshield trim loose
My windshield center trim has been singing in the wind for a while and my solution has been to tape it down. Today I had my windshield changed for the second time and the center section almost went awol on the way home. So, I need experienced opinions on a proper permanent solution. I've heard of using double sided tape, I don't see evidence of it being used from the factory however. Who has lived through this scenario and what was the resolution?
Les
Les
I did not think the clips on the trim were attached by double sided tape from the factory. I bought a spare top piece and one clip was loose. I pried it off and found double sided tape. It's a perfect fit under the clip and with exact holes where the locating pins are. I was still skeptical about the tape coming from the factory. I've check other ebay windshield trim listings and have seen the same tape where the clips have come off. I don't know if a consumer can buy double sided tape that would be as strong as the factory. Then again, based on how many have come loose, that may prove it's not the best way to attach the clips. I was thinking epoxy was a better solution.
Last edited by Toolman; 02-28-2015 at 10:03 PM.
Buy I still like epoxy better on something that is supposed to be more permanent.
Join Date: Mar 2011
Location: Lake Jackson, TX
Age: 34
Posts: 548
Likes: 0
Received 1 Like
on
1 Post
Re: Windshield trim loose
The first picture I posted in the 3rd. post shows the problem. I didn't know what I was looking at. 3 of the clips stayed connected to the receiving pieces on the car instead of staying on the trim. I extracted the 3 clips missing from the trim, cleaned off the tape and restored them to their rightful places on the trim with new 3M double sided tape. Pictures tell the tale.
It's back together again. Geez, if you want something done right you have to do it yourself.
Les
It's back together again. Geez, if you want something done right you have to do it yourself.
Les
Re: Windshield trim loose
I've used the double sided tape for other applications and found the 3M brand to be superior. In addition surface prep is essential, I typically use rubbing alcohol and try not to get any oils from my fingers on any of the surfaces or the tape. Once stuck it's pretty hard to remove without a lot of excessive heat.
Re: Windshield trim loose
After checking several sources for the 3M VHB (Very High Bond) double sided tape I settled on an ebay seller. This tape is extremely sticky. My first placement of the tape on the clip was not even. I found it hard to remove after only being on for a second. I'm very confident in it's holding power.
Here is a listing from that seller.
http://www.ebay.com/itm/3M-1-x-9-ft-3-Yd-VHB-Double-Sided-Foam-Adhesive-Tape-5952-Automotive-Mounting-/161393115204?hash=item2593c78044&item=161393115204&pt=Motors_Automotive_Tools&vxp=mtr
Here is a listing from that seller.
http://www.ebay.com/itm/3M-1-x-9-ft-3-Yd-VHB-Double-Sided-Foam-Adhesive-Tape-5952-Automotive-Mounting-/161393115204?hash=item2593c78044&item=161393115204&pt=Motors_Automotive_Tools&vxp=mtr
Re: Windshield trim loose
Hello guys,
I had the same problem after getting my windshield replaced. My original trim piece flew off when I was driving down the freeway.
Luckily, I found another piece from a local scrap yard. It was missing one clip; I used double sided 3M automotive tape to adhere one of the clips from my old trim which was still stuck in place. I used rubbing alcohol to prep the surfaces and I also used a clamp to ensure there was a proper bond.
I put it on today, however, the area above the new clip does not seem to sit as snug as the rest of trim. The rubber gasket is slightly raised in this area and I am afraid it will fly off again. Not sure what to do next...
I had the same problem after getting my windshield replaced. My original trim piece flew off when I was driving down the freeway.
Luckily, I found another piece from a local scrap yard. It was missing one clip; I used double sided 3M automotive tape to adhere one of the clips from my old trim which was still stuck in place. I used rubbing alcohol to prep the surfaces and I also used a clamp to ensure there was a proper bond.
I put it on today, however, the area above the new clip does not seem to sit as snug as the rest of trim. The rubber gasket is slightly raised in this area and I am afraid it will fly off again. Not sure what to do next...
Re: Windshield trim loose
It sounds to me like the new clip or several of the older clips haven't snapped together correctly. I had to install mine more than once for just that reason. I ended up starting at one end and snapped them in place one at a time. Once correctly in place you need to know how they come apart or you'll break the trim. i.e. tool between the clip and anchor.
Les
Les
Re: Windshield trim loose
It sounds to me like the new clip or several of the older clips haven't snapped together correctly. I had to install mine more than once for just that reason. I ended up starting at one end and snapped them in place one at a time. Once correctly in place you need to know how they come apart or you'll break the trim. i.e. tool between the clip and anchor.
Les
Les
Oh well, I guess after I get this second windshield replaced I can install it correctly this time around. I already got another 2 rock chips on this new one in less than 6 months...
Thread
Thread Starter
Forum
Replies
Last Post
55chevy
All Crossfires
2
09-13-2015 07:38 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)