Oil. Why should I use
Re: Oil. Why should I use
And i actually followed Mrmiata's link and then I started doing some research..I think I may try to "break new grounds" and try amsoil don't know if you guys here have tried it but it seems to be the best oil for your money..that's if I can find it in a store of course haha
Re: Oil. Why should I use
And i actually followed Mrmiata's link and then I started doing some research..I think I may try to "break new grounds" and try amsoil don't know if you guys here have tried it but it seems to be the best oil for your money..that's if I can find it in a store of course haha
Re: Oil. Why should I use
Whatever baby wants, baby gets. She drinks top-shelf oil, gas and tranny fluid. Just paid (~~sniff-sniff~~) $415 for oil and transmission fluid change. No, that was not a trans. flush. Was told it was some kind of mineral based fluid that it takes rather than whatever the dealership would've put in it. I plan to keep the car and plan to take good care of it........even if she is a picky little b***h when it comes to maintenance. Makes me feel like I'm not high maintenance at all compared to my car !
Re: Oil. Why should I use
That statement makes no sence at all.IMO
The hotter the temp, the higher the viscosity of the oil.
The viscosity of the oil only goes down at start up when the engine is cold.
Join Date: Jun 2009
Location: Fort Worth, Texas
Age: 64
Posts: 13,461
Received 886 Likes
on
690 Posts
Re: Oil. Why should I use
Cold Engine idle: 55 psi; Hot Engine Idle: 9 psi
My next change will be to Mobile 1 5W50
Re: Oil. Why should I use
So you're telling me the viscosity goes down as the temp goes up.?
Join Date: Jul 2009
Location: Central South Carolina
Age: 69
Posts: 5,850
Received 380 Likes
on
329 Posts
Re: Oil. Why should I use
OK, so now you're telling me the Viscosity actually goes down as the oil heats up too?
Could we be confusing "flow characteristics" with viscosity?
Last edited by +fireamx; 08-21-2012 at 07:05 PM.
Re: Oil. Why should I use
a SAE 30 motor oil is the same viscosity as a 10w-30 or 5W-30 at 210° (100° C). The difference is when the viscosity is tested at a much colder temperature. For example, a 5W-30 motor oil performs like a SAE 5 motor oil would perform at the cold temperature specified, but still has the SAE 30 viscosity at 210° F (100° C) which is engine operating temperature. This allows the engine to get quick oil flow when it is started cold verses dry running until lubricant either warms up sufficiently or is finally forced through the engine oil system. The advantages of a low W viscosity number is obvious. The quicker the oil flows cold, the less dry running. Less dry running means much less engine wear.
Still sounds like magic.
.And i thought it flowed like a 0 and lubed like a 30
5u7
Re: Oil. Why should I use
Or what are you saying exactly?
With Chrysler/MB saying an oil with the properties of 40 grade is good at our operating temperatures you have decided somehow that 50 grade is better. Please tell.
Remember that warranty work due to improper oil usage is something that the makers try to avoid. So they gave a recommendation that you choose to ignore.
In a warmer climate you really have no need for 0W-40 oil and 5W is fine, but 5W-50?
These cars with close tolerance engines need a thinner oil to get into the gaps and provide a bed for the moving parts, using an oil that is less able to access these gaps has got to be wrong to some extent. This isn't your clapped out Chevy Vega we are talking about here.
Last edited by onehundred80; 08-21-2012 at 07:55 PM.
Join Date: Jun 2009
Location: Fort Worth, Texas
Age: 64
Posts: 13,461
Received 886 Likes
on
690 Posts
Re: Oil. Why should I use
To some extent, yes.
The reason the oil pressure is high is because the pump cannot push the oil around so easily and it is also moving less oil, the pressure you see is back pressure.
So, no, I do not simply believe that a higher pressure is all there is to it.
With Chrysler/MB saying an oil with the properties of 40 grade is good at our operating temperatures you have decided somehow that 50 grade is better. Please tell.
Remember that warranty work due to improper oil usage is something that the makers try to avoid. So they gave a recommendation that you choose to ignore.
In a warmer climate you really have no need for 0W-40 oil and 5W is fine, but 5W-50?
Remember that warranty work due to improper oil usage is something that the makers try to avoid. So they gave a recommendation that you choose to ignore.
In a warmer climate you really have no need for 0W-40 oil and 5W is fine, but 5W-50?
And I am very **** about this - I would never put ANY oil in there that MB did not have on either 229.3 or 229.5 - Mobile 1 5W50 is on 229.3 (even shows up on the bottle).
5W50 IS approved for these engines.
These cars with close tolerance engines need a thinner oil to get into the gaps and provide a bed for the moving parts, using an oil that is less able to access these gaps has got to be wrong to some extent. This isn't your clapped out Chevy Vega we are talking about here.
The truck has had water pumps, a distributor, heater core, u joints, ball joints, alternators and a clutch replaced. The engine itself just keeps running.
But it really all goes to 229.3 and 229.5 - there are even two 10W and one 15W oils on 229.3 !!!!
What say you to THAT ??
Last edited by pizzaguy; 09-29-2012 at 09:22 PM.
Join Date: Jun 2009
Location: Fort Worth, Texas
Age: 64
Posts: 13,461
Received 886 Likes
on
690 Posts
Join Date: Jun 2009
Location: Fort Worth, Texas
Age: 64
Posts: 13,461
Received 886 Likes
on
690 Posts
Re: Oil. Why should I use
Re: Oil. Why should I use
In your climate a 5W-40 would be OK I guess, but not preferred.
Re: Oil. Why should I use
I love Mobil 1 oil, so I won't get into the brand argument. I use either the 0w-40 or 5w-40 period. You can't always find the zero....but 5w seems to always be on someone's shelf... I would think any name brand synthetic in those numbers would be fine. But, Mobil 1 has been a proven winner in all my cars since the early 80's and I am staying with it....
Re: Oil. Why should I use
There's a long extensive list of MB recommended oils for the 3.2 engine. Use any one of them you like. I've always used Mobil 1 0-40 and it's one of Mobil 1's better multi-viscosity oils if bill the oil guy is real. Because of my climate and car abusage I may switch to Mobil 1 5-50, if I can find it. Also on the recommended list BTW.
MB 229.3 - Multigrade engine oils (Specification 229.3) - Mercedes-Benz Specifications for Operating Fluids
Les
MB 229.3 - Multigrade engine oils (Specification 229.3) - Mercedes-Benz Specifications for Operating Fluids
Les
Join Date: Jun 2009
Location: Fort Worth, Texas
Age: 64
Posts: 13,461
Received 886 Likes
on
690 Posts
Re: Oil. Why should I use
There's a long extensive list of MB recommended oils for the 3.2 engine. Use any one of them you like. I've always used Mobil 1 0-40 and it's one of Mobil 1's better multi-viscosity oils if bill the oil guy is real. Because of my climate and car abusage I may switch to Mobil 1 5-50, if I can find it. Also on the recommended list BTW.
MB 229.3 - Multigrade engine oils (Specification 229.3) - Mercedes-Benz Specifications for Operating Fluids
Les
MB 229.3 - Multigrade engine oils (Specification 229.3) - Mercedes-Benz Specifications for Operating Fluids
Les
The Lubricant Store - 106035
I paid $140.36 with shipping for 18 quarts, that was $38.61 for six quarts plus shipping, I see the price is up to $49.70 for six quarts now.
I should have bought 20 cases.....
Re: Oil. Why should I use
Walmart has it .... sometimes. Most of my racing buddies use 15-50 (non Crossfire) brands like Mobil 1, Valvoline, Motul, Brad Penn, Jose Gibs, Shaefer etc. The old air cooled Porsche swears that Shaefer oil lowered his oil temperatures by 20º. I don't know. I road race or I wouldn't think of it.
Les
Les